purchased on craigslist for 600.00 Technical data Pro-Ject 2 Xperience Acryl Fitted cartridge optional Ortofon 2M Red Nominal speeds 33 / 45 r.p.m. Dust cover yes Record clamp yes Supplied Pro-Ject phono cable standard cable RCA phono sockets yes Sorbothane-damped aluminium cones yes Tonearm Pro-Ject 9cc Tonearm with fibre armtube and sapphire thrust-pads yes Effective tonearm length 9 " (230mm) Effective tonearm mass 8,5g Overhang 18mm Supplied counterweight cartridge weight 6 - 10g Optional counterweights cartridge weights 11 - 15g, 8 - 11g, 5 - 8g Downforce range 10 - 30mN Speed variance ±0,5 % Wow and flutter ±0,08 % Signal to noise -70dB Platter weight/diameter 2kg/300mm Power supply type Mains-fed outboard power supply 220 - 240V, 50 cycles or 100 - 110V, 60 cycles

purchased here for 1200.oo Gain: 10 dB (normal) 16 dB (high gain) Freq. Response: -3 dB @ 5 Hz -3 dB at > 100 kHz Distortion: < .01 % THD @ 2 volts rms balanced < 1% @ 18 volts rms balanced (normal) < 1% @ 40 volts rms balanced (high gain) Maximum Output: 18 volts rms. balanced out (normal) 40 volts rms. balanced out (high gain) Output Impedance: 1000 ohms each output polarity Input Impedance: 10 kOhm unbalanced 20 kOhm balanced CMRR: less than –50 dB, 20-20 KHz typically less than –67 dB @ 1 KHz Crosstalk: less than –60 dB, 20-20 KHz typically less than –80 dB @ 1 KHz Output Noise: 80 microvolts rms 20-20 KHz band unweighted Power Consumption: 30 watts

purchased on closeout for 599.00 SPECS & DETAILS 205W RMS Clean into 4-Ohm speakers, 180W RMS into 8-Ohm Speakers Best with speakers rated over 85db (higher is better), 2-Ohm to 16-Ohm Perfectly Flat Frequency Response 5Hz-50kHz, -3db 2Hz-200kHz Cutting Edge Design without feedback reveals recorded harmonic structures like a tube amplifier while maintaining solid state bass capabilities Features Soft Clipping like tube amps NO Coupling Caps, Directly Connected Part To Part for Zero Loss in Detail, Zero Phase Shift Blur 0.7V-RMS input for full power (normal CD player line level output) Easy to drive & match 46k Input Impedance Small volume knob on each amp to balance the room and adjust the input sensitivity. (0.7V to 20V) to match any preamp with RCA jacks Hibachi-II's have External Access Speaker Protection Fuses Supplied with 4-Amp speaker fuses for 200W rated speakers, Use 3-Amp speaker fuses for <200W speakers 17 Pounds Each 13-1/2" x 11" x 9" Tall to top of binding posts Giant toroidal high current 8-pound power transformer with smart sensing vacuum tube filter and huge film bypassed filter cap array Self test power up: Red light speaker disconnected for 2-seconds then relay clicks to Green light Draws very light current idling silent (12-watts), <1mV ripple hum, for convenience can be left on - read next line A Power Conditioner with relay disconnect surge protection is highly recommended to protect your valuable audio equipment Large WBT Style gold 5-way speaker wire binding posts accept all wire gauges Versatile high quality 4-Way Solid Nickel RCA's: Use one RCA for the normal mono block input. Combine L & R preamp signals on the amplifier using 2 RCA jacks to make mono for a center speaker. Has 2 more RCA jacks to easily daisy chain another amp for bi-amping. Can use the extra jacks for HT: Connect both your HT processor and your 2-chan preamp outputs to this amplifier at the same time - has a unique TAD designed isolation network on the RCA jacks.

purchased on closeout from needle doctor

Gain: (Selectable) 48/54/60/66dB Balanced Output 42/48/54/60dB Unbalanced Output Loading: (Selectable) 100/500/1k/47k ohms

Picked up used at AudioGon $1100 Nominal Impedance: 8 ohms Recommended Amplifiers: 20 to 100 watts Frequency Response: 30hz to 30Khz (+ or - 3db, 55hz-20Khz) Sensitivity: 86db linear for 1 watt at 1 metre Bass/Midrange Driver: ProAc 6 1 ⁄2” (165mm) polypropylene unit in die-cast chassis designed in conjunction with Scanspeak of Denmark. Special voice coil, pole piece, dustcap and magnet assembly. Tweeter: 3 ⁄4” (19mm) dome unit with honeycomb-wound voice coil. Special damping and ferrofluid-cooled coil assembly.